Auto




MSDS-PCM ABS 85%
구영서  2014-05-26 09:47:36, Hit : 2,608, Vote : 788

Material safety data sheet
                          
Grade name : ABS 3006

1. Chemical Product & Company Identification
   a. Chemical Product Name : Acrylonitrile, 1,3-Butadiene and Styrene Co-polymer
   b. Usage : Electronic Goods, Automotive Parts, Package, etc
   c.. Chemical Type : Thermoplastics
   d. Company's Address : Dowon Industry
         386-11, Hyeongokri, Cheongbuk-myun, Pyeongtaeksi, Gyeonggido, Korea
   e. Phone Number : +82-31-683-2293


2. Hazards Identification
   a. Threshold Limit
   b. Effect of overexposure
      . Eye Contact :Solid or dust may cause irritation or corneal injury due to mechanical action
      . Skin Contact : Essentially nonirritating to skin, Mechanical injury only
      . Skin Absorption : Unlikely due to physical properties
      . Ingestion : Unlikely due to physical state
      . Inhalation : Dust may cause irritation to respiratory
                   In case of breathing, fumes released from heated material
                   may cause respiratory irritation
      . Chronic Effects : Not Available
      . Mutagenicity : Not Available


3. Composition / Information On Ingredients
       Material type                                            CAS Number      Contents      
   ---------------------------------------------------------------------              
   a. ABS (Acrylonitrile-Butadiene-Styrene)         9003-56-9        90 ~ 100%
   b. Typical antioxidant                                           0 - 3%
   c. Typical lubricants                                             0 - 5%


4. First Aid Measures
   a. Eye Contact : Immediately rinse eyes with copious amount of running water
                   and seek medical advice
   b. Skin Contact : Essentially nonirritating to skin but rinse with copious water
   c. Ingestion : If vomiting occurs, lower the head to ease vomiting and seek medical advice
   d. Inhalation : In case of breathing, fumes released from heated material may
                 cause respiratory irritation
                 In case of inhaling dense smoke, immediately remove a person to fresh air.
                 If necessary, apply artificial respiration and seek medical attention immediately
   e. Mutagenicity : Not Available


5. Fire Fighting Measures
   a. Flammable Properties
      . Flash Point : None
      . Method Used : Not applicable
      . Auto Ignition Temperature : Not applicable
   b. Extinguishing Media : Usually use water and use extinguishing media appropriate to
          surrounding conditions
   c. Special Fire Fighting Procedure : Cool Containers with water spray. In closed stores, provide
          fire fighter with self-contained breathing apparatus in positive pressure mode
   d. Usual Fire and Explosion Hazards : Irritating gases and dense smoke

6. Accidental Release Measures
   a. Personal Precautions : Pellets or beads may present a slipping hazard
   b. Environmental Precautions : Keep out of irrigation ditches, sewers, and water supplies
         Spills should be collected to prevent contamination of waterways
   c. Cleanup : Sweep up


7. Handling and Storage
   a. Handling : Avoid formation of dust
        Keep bags always closed / Keep container lightly closed
        Avoid pellets / bags from getting wet
   b. Storage : Keep bags / containers in a well-ventilated place
        Avoid pellets / bags from getting wet

8. Exposure Controls / Personal Protection
   a. Engineering Controls : Good general ventilation should be sufficient for most conditions.
        Local exhaust ventilation may be necessary for some operations
   b. Personal Protective Equipment
      . Eye / Face Protection : Use safety glasses. If the is a potential for exposure to particles
        which could cause mechanical injury to the eye, wear chemical goggles
      . Skin Protection : No Precautions other than clean body-covering clothing should be needed
      . Respiratory Protection : For most conditions, no respiratory protection should be needed ;  
          however, if handling at elevated temperatures without sufficient ventilation, use an
          approved air-purifying respirator. In dusty atmospheres, use an approved dust respirator
   c. Exposure Guideline (s)
       Although some of the additives used in this product may have exposure
       guidelines, these additives are encapsulated in the product and
       no exposure would be expected under normal handling conditions


9. Physical And Chemical Properties
   a. Appearance : Pellet (Colored solid)
   b. Odor : Almost Odorless
   c. pH : Neutral
   d. Boiling Point : Not applicable
   e. Evaporation Rate : Not applicable at standard condition
   f. Specific Gravity : 1.06
   g. Vapor Pressure : Not applicable at standard condition
   h. Vapor Density : Not applicable at standard condition
   i. Solubility in Water : insoluble
   j. Solubility in other Solvent : Soluble in THF, Acetone and other analogous solvents



10. Stability and Reactivity
   a. Stability : Stable under normal condition
   b. Storage conditions to avoid : Avoid fire and heating above 60℃
   c. Incompatibility : None known
   d. Hazardous decomposition products : Not applicable
   e. Hazardous polymerization : Not occur


11. Toxicological Information
   See Section 3 for Potential Health Effects. For detailed toxicological data, write or call the address
   or phone number shown in Section 1.


12. Ecological Information
   a. Environmental Fate
     . Movement & Partitioning : No bioconcentration is expected because of the high molecular
      weight (MW>1000). In the terrestrial environment, material is expected to remain in the soil.
      In the aquatic environment, material will sink and remain in the sediment.
     . Degradation & Persistence : This water insoluble polymeric solid is expected to the inert in the
      environment. Surface degradation is expected with exposure to sunlight. No appreciable    
      biodegradation is expected.

   b. Ecotoxicity
      Not Expected to be acutely toxic, but pellets, if ingested by waterfowl
      or aquatic life, may mechanically cause adverse effects


13. Disposal Considerations
   Disposal : Do not Dump into any sewers, on the ground, or into any body of water.
   All disposal methods must be in compliance with all Federal, State/Provincial and local laws and
   regulations. Regulations may vary in different locations. Waste characterizations and compliance  
   with appliance laws are the responsibility solely of the waste generator.

   For unused & uncontaminated product, the preferred options include sending to a licensed,
   permitted
   : recycler, reclaim, incinerator or other thermal destruction device.


14. Transport Information
   Not classified as hazardous under transport regulations.


15. Regulatory Information
   Listed below are chemical substances subject to supplier notification requirements.

   U.S. REGULATIONS :
     TSCA INVENTORY STATUS : This product complies with the Chemical Substance Inventory
     requirements of the US EPA TSCA.
     CERCLA SECTION 103 (40CFR302.4) : Not Listed
     SARA SECTION 313 (40CFR372.65) : Not Listed
     SARA HAZARD CATEGORIES, SARA SECTIONS 311/312 (40CFR370.21)
       ACUTE : Not Listed
       CHRONIC : Not Listed
       FIRE : Not Listed
       REACTIVE : Not Listed
       SUDDEN RELEASE : Not Listed
    STATE REGULATIONS :
       California Proposition 65 : Not Listed
    EUROPEAN REGULATIONS :
       EC NUMBER : Not assigned
   This product complies with the requirements of resolution of European Parliament (WE) no.
   1907/2006 Dated December 18 2006 concerning REACH (European Union Official Register L396
   with its changes In EU Official Register no. L136)


16. Other Information
   Product should be handled, stored, and used in accordance with the generally accepted industrial
   hygiene practices and in conformity with all the applicable legal regulations.
   The information provided herein is based on the state of our knowledge and is intended to
   describe the product with regard to the requirements of safety.
   It should, therefore, not be construed as guaranteeing specific properties.


  Vote   List

NO SUBJECT WRITER DATE   VOTE HIT
2  MSDS-DW01    구영서 2014/05/26 699 2888
 MSDS-PCM ABS 85%    구영서 2014/05/26 788 2608

    List 1
       

/ skin by Digital Solution